Stranded Wire - Snap-In 120V IC Fixture Whip

    Our Illumination Control Fixture Whip (ICFW) is an integral component for illumination and control of all lighting systems. The ICFW can be used in new or retrofit construction for lighting systems operating at 120/277 VAC, meets all UL and NEC  standards for combining power and lighting circuits with Class 2 or Class 3 control circuits within the same fixture whip, and is the cost-effective solution that saves the contractor time and labor when compared to buying and terminating expensive five conductor MC Cable or making a homemade solution at the job site.

    The ICFW is easily integrated into the architecture of a building using LED luminaires or fluorescent luminaires with dimming ballast and digital controls to:

    • Optimize lighting at all times when used with an independent room controller for daylight harvesting as an energy management solution to reduce energy consumption.
    • Operate in compliance with "timed" daily personnel and warehouse schedules.
    • Control lighting operations used in combination with occupancy sensors for commercial and industrial applications.

    BENEFITS

    • UL Listed. File Number E87199.
    • Meets the requirements of the 2023 National Electrical Code, Article 300.3(C)(1), Section 725.136(I)(1), 725.139(A) through (D)(1) and California Title 24 Lighting Controls, Articles 130.1(A)(B)(C)(D)(E).
    • Meets UL and NEC Articles for combining Power / Lighting Circuits and the Class 2 or Class 3 Control Circuits all within the same Fixture Whip.
    • Easy to install and wire. Installation is familiar to electrical contractors and is less prone to installation error.

    How Does it Differ from EPCO's Standard 3/8" or 1/2" Fixture Whip?

    EPCO's Standard Fixture Whip is intended to exclusively connect the Line Voltage Conductors of an LED Driver or Ballast to the incoming Power Conductors within an Electrical Junction Box (Class 1 Circuit).

    Why is it Necessary to have a Different Fixture Whip Configuration than our Standard Whip when  a Luminaire will Utilize Wireless Lighting Controls?

    • Wireless Lighting Controls use Relay Modules that can be attached to the outside of an electrical junction box with a nipple.
    • The connection(s) of the low voltage conductors from the dimmable ballast or LED driver are intended to go through the Junction Box, and through the nipple and into the Lighting Control Relay Module to receive controller commands.
    • When the Electrical Contractor wants to use a single pre-fabricated Fixture Whip to control a luminaire with control features.

    TYPICAL APPLICATIONS

    • LED and Fluorescent Dimming
    • Smart Buildings
    • Daylight Harvesting Systems (saves energy)

    Contact the EPCO Inside Sales Department at 800.336.1976 or sales@engproducts.com for more specific information on other connector types available.

    Find out Why Contractors Use EPCO Fixture Whips »

    Image
    3-12 AWG Stranded Wire: 6-FT - 1/2" Conduit
    Catalog Number
    EPW1263AD-1/2-IC
    UPC Number
    84024
    Item Description
    Includes Die Cast Snap-In Connector; three (3) 12 AWG Stranded Wires - Black, White, and Green; two (2) 16 AWG Jacketed Control Wires - Purple and Pink
    Order Unit
    EA
    Unit Quantity
    1
    Unit Package
    BRL
    Unit Per Case
    100
    Total Case Quantity
    100
    Min. Order Quantity
    10
    Ship Weight
    292.00lbs.
    MM Req.
    Yes
    Image
    3-14 AWG Stranded Wire: 6-FT - 1/2" Conduit
    Catalog Number
    EPW1463AD-1/2-IC
    UPC Number
    84026
    Item Description
    Includes Die Cast Snap-In Connector; three (3) 14 AWG Stranded Wires - Black, White, and Green; two (2) 16 AWG Jacketed Control Wires - Purple and Pink
    Order Unit
    EA
    Unit Quantity
    1
    Unit Package
    BRL
    Unit Per Case
    100
    Total Case Quantity
    100
    Min. Order Quantity
    10
    Ship Weight
    282.00lbs.
    MM Req.
    Yes
    Image
    4-14 AWG Stranded Wire: 6-FT - 1/2" Conduit
    Catalog Number
    EPW1464AD-1/2-IC
    UPC Number
    84027
    Item Description
    Includes Die Cast Snap-In Connector; four (4) 14 AWG Stranded Wires - Black, Red, White, and Green; two (2) 16 AWG Jacketed Control Wires - Purple and Pink
    Order Unit
    EA
    Unit Quantity
    1
    Unit Package
    BRL
    Unit Per Case
    100
    Total Case Quantity
    100
    Min. Order Quantity
    10
    Ship Weight
    282.00lbs.
    MM Req.
    Yes
    Image
    3-16 AWG Stranded Wire: 6-FT - 1/2" Conduit
    Catalog Number
    EPW1663AD-1/2-IC
    UPC Number
    84030
    Item Description
    Includes Die Cast Snap-In Connector; three (3) 16 AWG Stranded Wires - Black, White, and Green; two (2) 16 AWG Jacketed Control Wires - Purple and Pink
    Order Unit
    EA
    Unit Quantity
    1
    Unit Package
    BRL
    Unit Per Case
    100
    Total Case Quantity
    100
    Min. Order Quantity
    10
    Ship Weight
    277.00lbs.
    MM Req.
    Yes
    Image
    4-16 AWG Stranded Wire: 6-FT - 1/2" Conduit
    Catalog Number
    EPW1664AD-1/2-IC
    UPC Number
    84031
    Item Description
    Includes Die Cast Snap-In Connector; four (4) 16 AWG Stranded Wires - Black, Red, White, and Green; two (2) 16 AWG Jacketed Control Wires - Purple and Pink
    Order Unit
    EA
    Unit Quantity
    1
    Unit Package
    BRL
    Unit Per Case
    100
    Total Case Quantity
    100
    Min. Order Quantity
    10
    Ship Weight
    272.00lbs.
    MM Req.
    Yes
    Image
    3-18 AWG Stranded Wire: 6-FT - 1/2" Conduit
    Catalog Number
    EPW1863AD-1/2-IC
    UPC Number
    84034
    Item Description
    Includes Die Cast Snap-In Connector; three (3) 18 AWG Stranded Wires - Black, White, and Green; two (2) 16 AWG Jacketed Control Wires - Purple and Pink
    Order Unit
    EA
    Unit Quantity
    1
    Unit Package
    BRL
    Unit Per Case
    100
    Total Case Quantity
    100
    Min. Order Quantity
    10
    Ship Weight
    270.00lbs.
    MM Req.
    Yes
    Image
    4-18 AWG Stranded Wire: 6-FT - 1/2" Conduit
    Catalog Number
    EPW1864AD-1/2-IC
    UPC Number
    84035
    Item Description
    Includes Die Cast Snap-In Connector; four (4) 18 AWG Stranded Wires - Black, Red, White, and Green; two (2) 16 AWG Jacketed Control Wires - Purple and Pink
    Order Unit
    EA
    Unit Quantity
    1
    Unit Package
    BRL
    Unit Per Case
    100
    Total Case Quantity
    100
    Min. Order Quantity
    10
    Ship Weight
    277.00lbs.
    MM Req.
    Yes
    Item DescriptionContractor Cost1 WhipExtended Cost
    12 AWG MC - 5 Wire$1100/M7.5' per Whip$8.25
    12 AWG MC - 5 WireScrap0.33' per Whip$0.36
    MC Connectors$0.50 Each2 Connectors/Whip$1.00
    Labor/Hour#30/Hour5 Whips/Hour$6.00
    Total Cost to Build Each ICFW$15.60